Walk-In Temperature Cycling Chamber
Customizable Environmental Test Chamber for Varied Applications
Our Walk-In Environment Chamber is the ideal solution for conducting a wide range of environmental tests, catering to the needs of entire machines or large components.This versatile chamber can simulate low temperatures, high temperatures, rapid temperature changes, constant heat exposure, as well as alternating high and low temperatures combined with moisture tests.
- Flexible Configuration: Our chambers are constructed using customizable modular panels, allowing for alterations in size and shape as per your specific requirements. They are assembled on-site for easy transport and relocation. To ensure superior sealing and durability, we use specially imported silicon rubber from Japan for sealing the joints. The frame structure design with integrated steel plates provides outstanding insulation, longevity, and resilience to various temperature and humidity conditions.
- Non-Frost Operation: Our chambers ensure non-frosting operation and feature an automatic defrosting loop, allowing continuous operation even in low humidity and low-temperature settings.
- Intuitive Control: The 7-inch color control screen provides a comprehensive display of the chamber's operational status, making it easy to monitor and manage the testing process.
- Energy Efficiency: Automatic precooling and preheating temperature settings based on time reset optimize the chamber's operating state, resulting in potential energy savings of up to 50% when compared to older models.
- Accurate and Uniform Testing: Our chamber is designed for low error, high wind speed, and consistent exposure of samples to ensure precise and uniform testing results.
- Low Noise Design: With noise levels controlled to under 72db, we prioritize a quiet testing environment without compromising performance.
|1.1 Temperature range||-40 to +150℃|
|1.2 Temp Deviation||≦ ± 2.0℃|
|1.3 Temp Fluctuation||±0.5℃|
|1.4 Temp Uniformity||±2.0℃|
|1.5 Heating up& cooling down rate||Heating up rate: RT ↑ +110℃ about 30min (no-load)
Cooling rate: +110℃ down to RT about 60min (no-load, )
|2.Humidity control range||10%R.H～98%R.H|
|Humidity uniformity||±3.0％RH(No load)|
|Temperature and humidity performance test is in accordance with the relevant provisions of the
IEC60068 -3 standard measurement; sensor placed in the unit outlet.
|Chamber size||All customize|
|Door||Single door, left open. Heating wire was installed at the door frames to prevent condensation at low temperatures.|
|4. Observation window||With observation window(according to design), multi-hollow electric insulation coated glass prevent condensation effectively|
|5. Lighting device||LED Lighting device *1 located on observation window|
|6. Heating||High quality nickel-chromium alloy wire electric heaters,
Non-contact control mode(SSR)
|7. Humidifier||Water basin heating and humidification method;
Stainless steel sheathed heater;
Heater control: no-contact control (SSR);
Water level control device, heater anti-dry device.
|8. Water outlet hole||Available for drain the condensate water|
|9. Cable port||Φ50mm*1 located on each side of chamber, with rubber
stopper and stainless steel cover
|10. Shelf for samples||No|
|11. Mobile Casters||Mobile Casters with foot cups|
|Electronic control cabinet||Total power circuit breakers, over-temperature protectors|
|Supply system||Pump to enhance automatic water supply|
● GB-2423．1-2008(IEC68-2-2) Test B: High Temperature Test
● GB-2423．1-2008(IEC68-2-2) Test B: Low Temperature Test
● GJB360．8-2009(MIL-STD．202F) High Temperature Operating Life Test
● GBJl50．3-2009(MIL-STD-810D) High Temperature Test
● GBJl50．4-2009(MIL-STD-810D) High Temperature Test
Experience the exceptional adaptability and reliability of our Walk-In Environment Chamber for all your environmental testing needs. Contact us today to discuss how we can tailor the chamber to your specific requirements.
#Manufacturer Indonesia Philiphines Thailand Vietnam Singapore
Inquiry - Walk-In Temperature Cycling Chamber